XBoard V2 - the bridge between home and Internet

Avaiability: In stock



The main improvement is that it now operates at 5V, making it compatible with most sensors and I2C protocol without the need of a voltage level converter.
it is a unique Arduino board which features a WIZnet ethernet port, an socket, and an ATMega328. This board will add wireless control as well as internet connectivity to your projects. It's great for anything from home automation to robot control. The possibilities are endless!
It has 8 Analog I/O pins and 8 digital pins, 4 of which have PWM (indicated by an asterisk). It is compatible with all modules, and also comes with an integrated socket for APC220 RF Module or DF-Bluetooth Module. it can be programmed via an FTDI programmer or via the ICSP header. Power is provided through a Mini USB connector. You can setup a web server through which you may communicate with a remote Arduino using radios, bluetooth or APC modules. This information can be posted to a web site, Twitter or other services.


  • MCU:Atmega328P low voltage version (16Mhz)
  • Ethernet:WIZ5100
  • Arduino Uno bootloader
  • Supply voltage:5~12v
  • Output voltage:5v/3.3v
  • Digital IO: 8
  • Analog In: 8
  • Envionment Friendly: Rohs Compliance
Informational LED
  • PWR: indicates that the board and shield are powered
  • LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
  • FULLD: indicates that the network connection is full duplex
  • 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
  • RX: flashes when the shield receives data
  • TX: flashes when the shield sends data
  • COLL: flashes when network collisions are detected

Optional Parts

  • 2mW Wire Antenna - Series 2(ZB) (TEL0020)
  • Bluno bee - Support wireless programming (TEL0073)
  • APC220 Radio Communication Module(TEL0005)
Note: By using the S2, the x-board will have the capability to establish a wireless network which is able to control up to 255 end points. Other wireless modules only support Point to Point communication.

  • USB Serial Light Adapter (DFR0164)

  • Cables
  • Mini USB cable(FIT0057)
  • Ethernet Cable(FIT0116)

  • Shipping List

    • X-Board V2 x1


    Project 1. Using the Arduino Xboard to control a relay
    In this project you will find how to use it with along with another arduino to control some objects over your local network.
    Hardware needed:
    • 1 Arduino
    • 1 Xboard
    • 1 FTDI programmer
    • 1 Relay
    • 1 CAT5 cable
    • 1 pair of modules
    • 1 computer
    • 1 Internet router
    • hookup wire

    Project 2. X-Board V2 and Pachube data on LCD
    This project reads feed data on Pachube and shows the data on an LCD. The project is quite simple. The following hardware was used:
    -X-Board v2 (DFR0162)
    -FTDI Basic Breakout (DFR0065) for uploading the sketch code to X-Board
    -LCD2004 display
    - USB Power adapter (FIT0197)
    -USB cable for power
    -Ethernet cable to connect it to router/internet

    Project 3. AutoEco System takes care of your garden
    By following this project it will help to grow a vegetable garden, and automate some other processes in our house along the way.
    List of basic hardware to setup an AutoEco Sys:

  • 1. Romeo
  • 2. X-Board
  • 3. Light Sensor
  • 4 .Gas Sensor
  • 5 .Motion Sensor
  • 6. Tempreture&Humidity Sensor
  • 7. Waterproof temperature sensor
  • Project 4. Make an X-Board Burglar Alarm

    Customer Reviews

    Review by n***5
    awsum (Posted on 5/18/2022)
    Review by j***9
    perfect (Posted on 5/18/2022)
    Review by a***3
    like it (Posted on 5/16/2022)
    Review by m***1
    Nice perfect (Posted on 5/16/2022)

    Write Your Own Review

    You're reviewing: XBoard V2 - the bridge between home and Internet

    Use spaces to separate tags. Use single quotes (') for phrases.